Insignia Kegerator Replacement Parts (2024)

1. NSBK1TSS6 Insignia Replacement Parts - PartStore.com

  • NSBK1TSS6 Insignia 5.6 Cu. Ft. 1-Tap Beverage Cooler Kegerator - Stainless Steel | PartStore.com replacement parts & accessories.

  • NSBK1TSS6 Insignia 5.6 Cu. Ft. 1-Tap Beverage Cooler Kegerator - Stainless Steel | PartStore.com replacement parts & accessories

2. NSBK2TSS6 Insignia Replacement Parts - Encompass

  • NSBK2TSS6 Insignia 5.6 Cu. Ft. 2-Tap Beverage Cooler Kegerator - Stainless Steel | Encompass replacement parts & accessories.

  • NSBK2TSS6 Insignia 5.6 Cu. Ft. 2-Tap Beverage Cooler Kegerator - Stainless Steel | Encompass replacement parts & accessories

3. Draft Beer Parts & Repair - KegWorks

4. Insignia Kegerators

  • Insignia is a Best Buy exclusive brand of kegerator available in single and double tap configurations and manufactured to keep the price low.

  • Insignia is a Best Buy exclusive brand of kegerator available in single and double tap configurations and manufactured to keep the price low. Keep the party flowing with Insignia kegerators at your next party.

5. Kegerator Parts - KegWorks

6. Insignia Parts - Repair Parts by Reliable Parts - Home Depot

  • Insignia Parts · BASKET · SWITCH (DOOR) · R SMALL TRAY · WIRE BASKET · DOOR LOCK · DRAIN HOSE (INNER) · Midea Refrigerator Glass Shelf ...

7. Insignia Single Tap Kegerator - NS-BK1TSS6

  • This Insignia NS-BK1TSS6 kegerator/beverage cooler holds either a 1/2 barrel keg or a 1/4 slim keg and features an adjustable thermostat, so you can easily ...

  • This Insignia NS-BK1TSS6 kegerator/beverage cooler holds either a 1/2 barrel keg or a 1/4 slim keg and features an adjustable thermostat, so you can easily keep your favorite drinks cold. Two wire shelves help you maintain organization.

8. Kegerator Parts List & Definitions

  • 8 jul 2014 · List of Parts: Faucet Handle; Faucet; Beer Tower; Guard Rail; Drip Tray; Regulator; CO2 Tube; CO2 Cylinder; CO2 Holder ...

  • Before you buy a kegerator, it would be wise to know the role each part plays to get that tasty beer in your glass. Let's take a closer look at these parts.

9. [PDF] Single- and Dual-Tap Kegerator/Beverage Cooler

  • determined to be defective by an authorized Insignia repair center or store personnel, Insignia will (at its ... parts; or (2) replace the Product at no charge ...

Insignia Kegerator Replacement Parts (2024)

FAQs

Why is beer not coming out of kegerator? ›

Ensure that the keg is not empty and that it is connected to the tap properly. If the keg is empty or not properly connected, the beer will not flow. It is also important to check the CO2 tank and regulator to ensure that they are functioning correctly.

How long will a keg last in a kegerator? ›

Keg beer will remain fresh if dispensing with CO2 while maintaining the proper temperature and pressure: For non-pasteurized draft beer, about 45-60 days. For pasteurized draft beer, about 90-120 days. NOTE: When dispensing keg beer with a party pump (air), any draft beer will remain fresh for no more than 8-12 hours.

How long does a CO2 tank last in a kegerator? ›

A 5-lb CO2 tank will last between 6-8 half barrels or full kegs before it needs to be filled. A 10-lb CO2 tank will dispense 10-13 full kegs per fill. This number can be higher or lower based on how often you're using your kegerator, the level of carbonation, and if your system is properly balanced.

How to troubleshoot a kegerator? ›

When beer is coming out slowly, there may be several contributing factors:
  1. Poorly connected lines: Ensure all beer lines are correctly connected and pressurized. ...
  2. Low pressure: Check that your keg is operating at the correct pressure levels. ...
  3. Low CO2 tank: Check the CO2 tank and verify it is not empty or running low.

Why is my CO2 not flowing into my keg? ›

Frozen or broken regulator:

You can check this by removing the tap from your keg and leaving it in the open position. Turn the control screw and see if you can decrease the volume of gas escaping from the tap. If you cannot change that flow, you will most likely need a new regulator or a rebuild job.

Why is my keg beer flat and foamy? ›

If your serving pressure is too high, it can pump excess co2 into the keg and lead to foaming. Check your regulator and adjust as required. If your serving pressure is too low, you may notice air pockets and bubbles in the beer line, causing foaming. Increase the serving pressure to ensure a solid flow.

What are the parts of a coupler? ›

Parts like knuckle, lock etc, are assembled in the coupler head to enable coupling and uncoupling. Tail end of the draw bar is provided with UIC stabilizing link and connects to the draft gear through the central pin. A backlash compensation device is assembled in the shank at tail end of coupler head.

What all do I need for a kegerator? ›

It is typically equipped with beer (or beverage) and air lines, an air (CO2 or Nitrogen beer gas) tank, a regulator, a draft beer tower, and a faucet. The beer keg is kept at a consistent temperature and carbonation level, allowing for a perfect pour every time. They can be used for either home or commercial use.

Top Articles
Latest Posts
Article information

Author: Twana Towne Ret

Last Updated:

Views: 5498

Rating: 4.3 / 5 (64 voted)

Reviews: 95% of readers found this page helpful

Author information

Name: Twana Towne Ret

Birthday: 1994-03-19

Address: Apt. 990 97439 Corwin Motorway, Port Eliseoburgh, NM 99144-2618

Phone: +5958753152963

Job: National Specialist

Hobby: Kayaking, Photography, Skydiving, Embroidery, Leather crafting, Orienteering, Cooking

Introduction: My name is Twana Towne Ret, I am a famous, talented, joyous, perfect, powerful, inquisitive, lovely person who loves writing and wants to share my knowledge and understanding with you.